?? 4 MTs #1 on VCN1000
#1
02-24-2006 | 01:18 PM
Thread Starter
|
Senior Member
Joined: Dec 2004
Posts: 383
From: Colorado
?? 4 MTs #1 on VCN1000
Hey Blake! I havent really looked into it but would it be much different to install an MSD window switch on our type of system? I been thinkin about getting one so i wouldnt have to spray out of the hole :helpsmili
#2
02-24-2006 | 01:36 PM
Senior Member
Joined: Nov 2004
Posts: 1,787
From: Murfreesboro, TN
All you do is connect the nitrous system's ground wire to the window switch. Thats the only way unless you want to open up the Venom control box. It would cut the entire system on or off whenever you hit the RPM's. Doesnt the Venom system take a second before its ready to spray though. Dont you have to wait on the green light?
If so you can take apart the Venom box (which I wouldnt do) and locate the nitrous solenoids ground wire. You then would just connect that to the window switch. You will need a tach adapter.
People will tell you that you dont need one because of the venom A/F ratio switch, but this would be a much safer way of cutting the spray off. Plus you can drive without spraying it out of the hole.
The real fun is when you floor it at 1500RPM's then wait for the window switch to cut the spray on.
If so you can take apart the Venom box (which I wouldnt do) and locate the nitrous solenoids ground wire. You then would just connect that to the window switch. You will need a tach adapter.
People will tell you that you dont need one because of the venom A/F ratio switch, but this would be a much safer way of cutting the spray off. Plus you can drive without spraying it out of the hole.
The real fun is when you floor it at 1500RPM's then wait for the window switch to cut the spray on.
#3
02-24-2006 | 02:13 PM
Administrator
Joined: Sep 2004
Posts: 6,613
Sam:
There is an easier way! Call Venom! Your system is setup and already pre-wired so you can add a push button activation. I think all you would need to do is hook up the window switch to those same wires. Instead of using the push button, you just use the window switch. It should work great. As long as the window swicth will give you a closed signal in a specific rpm range, it should spray.
Don't wire the window switch to the solenoid or anywhere else. Teh solenoid is connected to the Venom control module directly and the computer needs to see that the solenoid is hooked-up and operational, otherwise you will get an error.
You do not need to pull anything apart. The Venom system is the most sophosticated, yet simple system on the market. It does nto need to be re-engineered, just utilize what it already has.
There is an easier way! Call Venom! Your system is setup and already pre-wired so you can add a push button activation. I think all you would need to do is hook up the window switch to those same wires. Instead of using the push button, you just use the window switch. It should work great. As long as the window swicth will give you a closed signal in a specific rpm range, it should spray.
Don't wire the window switch to the solenoid or anywhere else. Teh solenoid is connected to the Venom control module directly and the computer needs to see that the solenoid is hooked-up and operational, otherwise you will get an error.
You do not need to pull anything apart. The Venom system is the most sophosticated, yet simple system on the market. It does nto need to be re-engineered, just utilize what it already has.
#4
02-24-2006 | 03:07 PM
Thread Starter
|
Senior Member
Joined: Dec 2004
Posts: 383
From: Colorado
Thanx fellas, I appreciate the input! Ill have to bust out my manual for my system just to make sure!
Iam pretty confident with the system,s WOT activation. I just wanted to find a way to activate itself from 2nd gear on.. I figure a window switch be the answer.
Iam pretty confident with the system,s WOT activation. I just wanted to find a way to activate itself from 2nd gear on.. I figure a window switch be the answer.
Thread
Thread Starter
Forum
Replies
Last Post
