Modular 4.6L Tech For all your 1996-2005+ 2V, 3V, and 4V modular motor needs.

fuel injector ?'s

Thread Tools
 
Search this Thread
 
Old Jun 8, 2007 | 06:56 PM
  #1  
mpt_1962's Avatar
Thread Starter
|
Senior Member
Joined: Jun 2007
Posts: 1,041
From: Twentynine Palms, CA
Default fuel injector ?'s

if im upgrading the cam i have to upgrade the fuel injectors right? Any suggestions on size? Do i need to upgrade the fuel pump too?
 
Old Jun 8, 2007 | 09:06 PM
  #2  
bassman97's Avatar
blank
Joined: Jun 2006
Posts: 2,451
From: North Jersey
Default

You should be fine w/ the stock pieces unless you throw ported heads and long tubes into the mix.
 
Old Jun 9, 2007 | 07:10 AM
  #3  
spike_africa's Avatar
Administrator
Joined: Sep 2004
Posts: 11,974
From: Orlando,Florida
Default

check out your other post.
 
Old Jun 9, 2007 | 07:28 AM
  #4  
r3dn3ck's Avatar
Wowbagger hates me too!
Joined: Nov 2005
Posts: 9,865
From: Magrathea/California
Default

injectors support a specific HP level. Nothing else. If you upgrade a cam and that adds 50-100hp you may just want new injectors but it's completely probable that you don't. more details on the car, the cam and the current setup and we can be more helpful.
 
Old Jun 9, 2007 | 08:59 AM
  #5  
mpt_1962's Avatar
Thread Starter
|
Senior Member
Joined: Jun 2007
Posts: 1,041
From: Twentynine Palms, CA
Default

well i have....
shorty headers, x-body off road w/no cats, 75mm throttle body, CAI, upgrading the cam, upgrading coils, and possibly intake manifold...should i upgrade the injectors now?
 
Old Jun 9, 2007 | 09:05 AM
  #6  
r3dn3ck's Avatar
Wowbagger hates me too!
Joined: Nov 2005
Posts: 9,865
From: Magrathea/California
Default

like we said... no. THere's nothing there that's going to make any more power than stock.
 
Old Jun 10, 2007 | 07:54 AM
  #7  
spike_africa's Avatar
Administrator
Joined: Sep 2004
Posts: 11,974
From: Orlando,Florida
Default

and dont bother with the coils or intake manifold upgrade ona 2v motor you will gain little and spends LOTS!!! spend your money elsewhere.
 
Old Jun 10, 2007 | 08:37 AM
  #8  
r3dn3ck's Avatar
Wowbagger hates me too!
Joined: Nov 2005
Posts: 9,865
From: Magrathea/California
Default

w00t!
 
Old Jun 10, 2007 | 12:30 PM
  #9  
mpt_1962's Avatar
Thread Starter
|
Senior Member
Joined: Jun 2007
Posts: 1,041
From: Twentynine Palms, CA
Default

so when i upgrade my heads i should upgrade the coils, injectors and intake manifold then?
 
Old Jun 10, 2007 | 12:32 PM
  #10  
mpt_1962's Avatar
Thread Starter
|
Senior Member
Joined: Jun 2007
Posts: 1,041
From: Twentynine Palms, CA
Default

oh yeah, when i get back from iraq im swapping out the shorty headers for long tube...i dont like the shorty ones at all...
 
Old Jun 10, 2007 | 12:40 PM
  #11  
bassman97's Avatar
blank
Joined: Jun 2006
Posts: 2,451
From: North Jersey
Default

The problem w/ the manifold and coils is that they are very efficant from the factory. You use to have a single 40,000V coil for all cylinders instead of individual ones for each cylinder so you get the idea on how good they are. However, injectors may need to be upgraded, depending on how much power you are putting out.
 
Old Jun 10, 2007 | 01:00 PM
  #12  
mpt_1962's Avatar
Thread Starter
|
Senior Member
Joined: Jun 2007
Posts: 1,041
From: Twentynine Palms, CA
Default

with all the new parts i was given an estimate of 300-325...thats after the long tubes are installed and the cam. I have other upgrades too though, i mentioned above. But the cam is the biggest upgrade besides the long tube headers and the stlall converter im putting in. im thinking about taking out the 4.10s and putting in 3.73...bad idea or good?
 
Old Jun 10, 2007 | 02:27 PM
  #13  
r3dn3ck's Avatar
Wowbagger hates me too!
Joined: Nov 2005
Posts: 9,865
From: Magrathea/California
Default

leave the 4.10's in. You'll probably fall short of 300rwhp but it should be fairly close. Leave the coils alone. Stock is fine. Stock replacement if you need them only. Injectors as power requires. Until you put in a power adder 24's are more than sufficient.Stock 19's are usually fine.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
hypnoticjoker
Modular 4.6L Tech
2
Aug 29, 2008 06:30 AM
Specster
Modular 4.6L Tech
2
Mar 23, 2008 02:22 PM
ANDYS87
Modular 4.6L Tech
5
Feb 13, 2007 02:01 PM
Bwhipple
Modular 4.6L Tech
8
Nov 1, 2006 01:25 PM
Othic
The Parts Desk
1
Aug 1, 2006 04:59 AM




All times are GMT -7. The time now is 07:50 AM.