General Tech Forum Use this form for tech related topics that relate to all/most Mustang platforms

Newly installed clutch burning smell

Old Nov 15, 2008 | 08:47 PM
  #1  
SpetsACDC's Avatar
Thread Starter
|
Likes gummy bears
Joined: Feb 2006
Posts: 68
From: TN
Default Newly installed clutch burning smell

I just installed a new clutch in my 99 v6. I tested the car out, and it seems to work. The throwout bearing is 100 times better, and I also replaced the clutch fork and pivot stud because they were squeaking. The clutch feels very different. It catches a lot sooner, and it is very smooth when the clutch actually connects with the engine. The actual clutch pedal feels looser (it is easier to push down). I'm not really sure I like it, but I'm prolly just used to the way it was.

After driving it maybe 1/2 a mile, I could smell something burning. It wasn't too strong, but definately there. I'm hoping it is just because it is brand new... It is kind of a "clean burning" smell if that makes since. It isn't strong like from a fire, but it reminds me of steam or like slightly burnt cookies without the cookie smell. Hah that makes no since.

Anyone know if this is normal, maybe like the face of the clutch needs to get worn down a little or something? I did resurface my flywheel, and everything else seems fine.


Thanks
 
Old Nov 17, 2008 | 06:24 AM
  #2  
TUFF 4.6's Avatar
"Just Add Foot"
Joined: Dec 2007
Posts: 2,250
From: Richmond Va.
Default

Sounds like everything is OK, its normal to get a little smell for a short time. Drive it awhile and keep an eye on it. What clutch did you put in? (aftermarket performance or reman)
 
Old Nov 17, 2008 | 02:46 PM
  #3  
SpetsACDC's Avatar
Thread Starter
|
Likes gummy bears
Joined: Feb 2006
Posts: 68
From: TN
Default

I bought a griptech clutch off ebay. It should be oem quality. The only bad thing that I thought of was... I used to have like 2-3 inches to let up before the clutch started to catch the engine. Now, it is almost as soon as I lift up my foot. So I thought maybe when I have the clutch pressed in, it is barely separated. However, the rpm's do not change, and nothing bad happens when I press the clutch in, so I think it really is disconnected.

Is there any way to adjust it so I can let up like 2-3 inches before it catches? I did that auto-adjusting thing where you just lift the clutch pedal towards the driver's seat.


Thanks
 
Old Nov 17, 2008 | 06:59 PM
  #4  
bassman97's Avatar
blank
Joined: Jun 2006
Posts: 2,451
From: North Jersey
Default

Griptech, off eBay? I hope you're lucky because 99% of time, off brand stuff sold on eBay is crap.
 
Old Nov 17, 2008 | 07:24 PM
  #5  
SpetsACDC's Avatar
Thread Starter
|
Likes gummy bears
Joined: Feb 2006
Posts: 68
From: TN
Default

I researched it before I bought it. They are reputable and have good quality parts.
 
Old Nov 17, 2008 | 07:49 PM
  #6  
spike_africa's Avatar
Administrator
Joined: Sep 2004
Posts: 11,974
From: Orlando,Florida
Default

You need to adjust the clutch with the stock setup all you do is have the car off and put it in first gear. Then pull up on the clutch with your foot under the pedal it wont go far but pull on it hard. Then press down slowly all the way to the floor. This will adjust the clutch and adjust to your driving style.
 
Old Nov 18, 2008 | 12:17 AM
  #7  
Leonide's Avatar
Avatar just for Jack
Joined: Feb 2008
Posts: 1,035
From: Whitehall, Ohio
Default

Originally Posted by spike_africa
You need to adjust the clutch with the stock setup all you do is have the car off and put it in first gear. Then pull up on the clutch with your foot under the pedal it wont go far but pull on it hard. Then press down slowly all the way to the floor. This will adjust the clutch and adjust to your driving style.
i did not know that. a nice bit of information.
 
Old Nov 18, 2008 | 04:54 AM
  #8  
Bwhipple's Avatar
In hibernation
Joined: Jun 2006
Posts: 318
From: Central PA
Default

You might also consider getting a firewall clutch adjuster.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
venom
The Reference Section
1
Jul 26, 2010 07:25 AM
elbarto
V6 Tech Forums
1
Oct 8, 2008 02:02 PM
TayWolf55
Videos
13
Dec 14, 2006 12:31 PM
03MustanGT
Pictures
16
Jul 10, 2006 05:32 PM
MacD02Stang
Pictures
32
Oct 28, 2005 08:55 PM


Thread Tools
Search this Thread

All times are GMT -7. The time now is 12:13 AM.