Bullitt intake conversion on 04 gt (misc parts ?)
#1
Bullitt intake conversion on 04 gt (misc parts ?)
Hi Randy,
If I've already got the bullitt intake, throttle body, throttle cables and cruise control what other parts will I need to install on my 04 gt and how much will it run me?
Thanks!
If I've already got the bullitt intake, throttle body, throttle cables and cruise control what other parts will I need to install on my 04 gt and how much will it run me?
Thanks!
#3
I did the swap on my 03.
Throttle Cable 1R3Z-9A758-BA
Throttle Control Bracket 1R3Z-9728-BA
Alternator Bracket 2R3Z-10153-AA
Intake Gaskets (2) YL3Z-9439-BA
Throttle Body/ gasket- Bullitt or 96-98 Cobra 2R3Z-9E926-AB. Gasket part #, F7LZ-9E936-AA
Cruise Control Cable 1R3Z-9A825-DA (Optional)
"L" Bracket 2R3Z-9J444-AA (I used something I found at Home Depot)
EGR Tube 1R3Z-9D477-CA or EGR Delete
Spacer Gasket 2R3Z-9E930-AA (Goes between the lower manifold and the upper plenum. It should already come with this)
T-Stat Housing 1W7Z-8592-AA (I was able to reuse my stock stuff)
Under intake hose 1R3Z-8260-DA (I used heater hose)
Crankcase Vent Tube 1R3Z-6C324-AA (Tube going from drivers side valve cover to inlet tube. I used heater hose for this too.)
Alternator
Bullitt fuel rails
4g to 6g plug from paperformance for new alt. or wire it up yourself. The plug is only ~$36 shipped
Inlet Tube (You can buy a new one or make your own) I still have my old C&L inlet tube I used with the Bullitt swap. PM me if you want it.
Valve covers with oil fill on drivers side (You can make a new inlet tube to fit around the pass. side oil fill)
Throttle Cable 1R3Z-9A758-BA
Throttle Control Bracket 1R3Z-9728-BA
Alternator Bracket 2R3Z-10153-AA
Intake Gaskets (2) YL3Z-9439-BA
Throttle Body/ gasket- Bullitt or 96-98 Cobra 2R3Z-9E926-AB. Gasket part #, F7LZ-9E936-AA
Cruise Control Cable 1R3Z-9A825-DA (Optional)
"L" Bracket 2R3Z-9J444-AA (I used something I found at Home Depot)
EGR Tube 1R3Z-9D477-CA or EGR Delete
Spacer Gasket 2R3Z-9E930-AA (Goes between the lower manifold and the upper plenum. It should already come with this)
T-Stat Housing 1W7Z-8592-AA (I was able to reuse my stock stuff)
Under intake hose 1R3Z-8260-DA (I used heater hose)
Crankcase Vent Tube 1R3Z-6C324-AA (Tube going from drivers side valve cover to inlet tube. I used heater hose for this too.)
Alternator
Bullitt fuel rails
4g to 6g plug from paperformance for new alt. or wire it up yourself. The plug is only ~$36 shipped
Inlet Tube (You can buy a new one or make your own) I still have my old C&L inlet tube I used with the Bullitt swap. PM me if you want it.
Valve covers with oil fill on drivers side (You can make a new inlet tube to fit around the pass. side oil fill)
Thread
Thread Starter
Forum
Replies
Last Post