Modular 4.6L Tech For all your 1996-2005+ 2V, 3V, and 4V modular motor needs.

well the x is on

Thread Tools
 
Search this Thread
 
  #1  
Old 11-16-2005 | 07:25 AM
StangGT804's Avatar
Thread Starter
|
Shut Up & Lift
Joined: May 2005
Posts: 1,304
From: New London, CT
Default well the x is on

well the bassani x is on!! sounds great!! i will have some clips up in a few weeks! saving up for a camcorder! But umm, theres a loud rattle mostly on the passenger rear side of the car. I hear it At low rpms, when i hit bumps, and when i reverse! I dont know exactly what it is, but it SUCKS!! I think its the pipes hitting one another or another pipe, but im not sure. Does anyone know or can help?? Its ss bassani x with cats, do they fit properly or what?!//?
 
  #2  
Old 11-16-2005 | 02:42 PM
Lances03SVT's Avatar
Super Moderator
Joined: May 2005
Posts: 9,684
From: Carthage, Missouri
Default

You will just have to do a little adjusting thats all.Congrats on the X pipe.
 
  #3  
Old 11-16-2005 | 02:47 PM
Shambles's Avatar
Sigma Beta Rho Soldier
Joined: Mar 2005
Posts: 2,682
From: Philadelphia, PA
Default

Could be the header bolt on the passenger side.
 
  #4  
Old 11-16-2005 | 03:01 PM
StangGT804's Avatar
Thread Starter
|
Shut Up & Lift
Joined: May 2005
Posts: 1,304
From: New London, CT
Default

Needs to be tightened?? Is that it? And lances, what do you mean by adjusting? Moving the pipes around, so it will not be rubbing against anything?? Cause everytime i reverse, turn on/off the car, low rpms, and bumps i HEAR that awful noise!

the noise is like near the trunk or rear wheel; on the passenger side!
 
  #5  
Old 11-16-2005 | 04:07 PM
Lances03SVT's Avatar
Super Moderator
Joined: May 2005
Posts: 9,684
From: Carthage, Missouri
Default

Yes you will have to look around and see where it is hitting and adjust it from there.
 
  #6  
Old 11-16-2005 | 04:20 PM
StangGT804's Avatar
Thread Starter
|
Shut Up & Lift
Joined: May 2005
Posts: 1,304
From: New London, CT
Default

ok thanks guy! ill check it out tom and let you guys know! thanks!!
 
  #7  
Old 11-16-2005 | 04:21 PM
Lances03SVT's Avatar
Super Moderator
Joined: May 2005
Posts: 9,684
From: Carthage, Missouri
Default

No problem.I had too adjust my catback after a few days.Since then no problems.
 
  #8  
Old 11-17-2005 | 09:05 AM
StangGT804's Avatar
Thread Starter
|
Shut Up & Lift
Joined: May 2005
Posts: 1,304
From: New London, CT
Default

Yea, i found the problem. The pipe on the right side, is rubbing against some metal support frame underneath the car! so, i guess the vibrating or whatever, was causing the rattle. So just a few adjustments and im SET! thanks for the comments guys
 
  #9  
Old 11-17-2005 | 10:09 AM
MachGT's Avatar
Senior Member
Joined: Jan 2005
Posts: 650
From: Iowa
Default

I had the same problem when I put my catback on, it was hitting the swaybar. I adjusted it and it went away
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
foncarelli
The Lounge
30
10-16-2006 11:35 AM
m0nkeh
The Lounge
32
01-02-2006 12:54 PM
MachGT
Pictures
9
03-30-2005 06:42 AM
madmatt
Modular 4.6L Tech
12
02-19-2005 12:00 AM
madmatt
The Lounge
2
01-30-2005 12:30 PM




All times are GMT -7. The time now is 10:28 PM.