bottle warm time?

bullitt 1600 · 04-28-2008, 06:07 PM

I think it dont work cuz it dont warm ip fast enough. How long does it take?

spike_africa · 04-28-2008, 07:11 PM

Takes around 5 mins before i see any temp change on the gauge. You should be able to feel the heater actully getting hot to the touch.

bullitt 1600 · 04-28-2008, 11:30 PM

I remmber it working well when my buddy installed it. The band was hot. Just not that hot. Does the gauge rise up even tho the bottle ain't open. It should right? I live in begs and I leave it in the trunk and it never goes higher then 930 or 950. I madeth mistake of leaving the bottle open all week ( in act) andit still never got hot. It has n2o cuz I'm able to purge

spike_africa · 04-29-2008, 08:44 AM

It wont change the reading unless the bottle is open other wise the pressure isn't in the line and thus your bottle pressure gauge isn't doing shit. They don't get that hot around 85* is what they heat up to. And just because you can purge doesn't mean there is alot of nitrous in there. Once they get low around say 1lb or less your bottle will be very hard to get any pressure out of it. The less nitrous you have in the bottle the longer it takes to heat it up and get enough pressure. I usually take mine out once they get below say 800 psi with the heater on and top them off to get topped off. They normally have 1-2 lbs of nitrous in them.

bullitt 1600 · 04-29-2008, 11:31 AM

that sux! it could then b that i need to refill. i only used it like 3 times tho.

TUFF 4.6 · 05-09-2008, 04:48 PM

Quote:

Originally Posted by bullitt 1600

that sux! it could then b that i need to refill. i only used it like 3 times tho.

What did you think when you hit the button?

bullitt 1600 · Yesterday, 07:03 PM

y buddy says its the sparki plugs. It sputters at full throttle. Where does the needle have to b for a good psi?

spike_africa · Yesterday, 09:27 PM

depends on what make your kit is, most are around 1,000psi.

04-28-2008, 06:07 PM	#1 (permalink)
bullitt 1600 Junior Member Join Date: Jun 2007 Posts: 23	bottle warm time? I think it dont work cuz it dont warm ip fast enough. How long does it take?

04-28-2008, 07:11 PM	#2 (permalink)
spike_africa Administrator Join Date: Sep 2004 Location: Orlando,Florida Posts: 6,657	Takes around 5 mins before i see any temp change on the gauge. You should be able to feel the heater actully getting hot to the touch. __________________ Dustin 2002 GT Mustang 5-Speed Drag Radials,Sprayed,Powershifted WOOO HOOOO!

04-28-2008, 11:30 PM	#3 (permalink)
bullitt 1600 Junior Member Join Date: Jun 2007 Posts: 23	. I remmber it working well when my buddy installed it. The band was hot. Just not that hot. Does the gauge rise up even tho the bottle ain't open. It should right? I live in begs and I leave it in the trunk and it never goes higher then 930 or 950. I madeth mistake of leaving the bottle open all week ( in act) andit still never got hot. It has n2o cuz I'm able to purge

04-29-2008, 08:44 AM	#4 (permalink)
spike_africa Administrator Join Date: Sep 2004 Location: Orlando,Florida Posts: 6,657	It wont change the reading unless the bottle is open other wise the pressure isn't in the line and thus your bottle pressure gauge isn't doing shit. They don't get that hot around 85* is what they heat up to. And just because you can purge doesn't mean there is alot of nitrous in there. Once they get low around say 1lb or less your bottle will be very hard to get any pressure out of it. The less nitrous you have in the bottle the longer it takes to heat it up and get enough pressure. I usually take mine out once they get below say 800 psi with the heater on and top them off to get topped off. They normally have 1-2 lbs of nitrous in them. __________________ Dustin 2002 GT Mustang 5-Speed Drag Radials,Sprayed,Powershifted WOOO HOOOO!

04-29-2008, 11:31 AM	#5 (permalink)
bullitt 1600 Junior Member Join Date: Jun 2007 Posts: 23	ma'an that sux! it could then b that i need to refill. i only used it like 3 times tho.

Yesterday, 07:03 PM	#7 (permalink)
bullitt 1600 Junior Member Join Date: Jun 2007 Posts: 23	y buddy says its the sparki plugs. It sputters at full throttle. Where does the needle have to b for a good psi?

Yesterday, 09:27 PM	#8 (permalink)
spike_africa Administrator Join Date: Sep 2004 Location: Orlando,Florida Posts: 6,657	depends on what make your kit is, most are around 1,000psi. __________________ Dustin 2002 GT Mustang 5-Speed Drag Radials,Sprayed,Powershifted WOOO HOOOO!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode