 |
|
| Register | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
|
||||||
| General Tech Forum Use this form for tech related topics that relate to all/most Mustang platforms |
 |
|
|
Thread Tools | Display Modes |
11-04-2005, 06:41 PM
|
#1 (permalink) |
|
Junior Member
Join Date: Nov 2005
Location: Los Angeles
Posts: 3
 |
Black Projector Headlights (99-04)
Hey does anyone know how to swap out the stock projector light bulbs? I just bought the PIAA H1 & H3 bulbs but im having a hard time taking it apart...
 |
|
|
|
11-04-2005, 06:47 PM
|
#2 (permalink) |
|
Senior Member
Join Date: Dec 2004
Location: Racine, WI
Posts: 10,243
 |
reach behind the lamp and twist and pull. youll feel when its ready to be pulled out. it should take you 30 seconds to do both.
|
|
|
|
|
11-04-2005, 06:49 PM
|
#3 (permalink) |
|
Junior Member
Join Date: Nov 2005
Location: Los Angeles
Posts: 3
|
do i have to take out any of the screws inside the shell???
|
|
|
|
|
11-04-2005, 06:55 PM
|
#4 (permalink) |
|
Junior Member
Join Date: Nov 2005
Location: Los Angeles
Posts: 3
|
--------------------------------------------------------------------------------
do i have to take out any of the screws inside the shell??? |
|
|
|
|
11-04-2005, 07:21 PM
|
#5 (permalink) |
|
Administrator
Join Date: Sep 2004
Posts: 6,374
|
It is really simple. Did you figure out how to pull the head light unit out yet? You need to do that first, then unplug the wire harness going to the bulb. Then twist-off the plastic holder that holds the bulb and pull the bulb out.
__________________
 Black 2000 GT Vert: Novi-2000 with Intercooler (375rwhp @ 9 psi); Tune by Kauffmans; Roush 380R Body kit; Steeda Subframes; Steeda Strut Tower Support; Deep Dish Bullets; FRPP 4:10's; SCT 4 Position Chip with four custom tunes; Steeda CAI; C&L Pleum; BBK 75 TB; SLP Loudmouth; SLP Catted X-Pipe; Bullitt Suspension; UPR Conrol Arms; Focus Fuel Pump My Car My Email |
|
|
|
|
11-05-2005, 11:33 AM
|
#6 (permalink) |
|
Member
Join Date: Jun 2005
Location: maryland
Posts: 78
|
yea on the projector lamp theres a cover with three (maybe four) screws. The h3 bulb has a set screw that holds a latch down. loosen that then theres one white wire that goes to the bulb that you pull to disconect....put the new bulb in and screw back on the set screw and back plate and your set
ummm the high beems i have no clue how u reach though so good luck on that one??
__________________
2004 GT: steeda cai, magnapack CB, magnaflow tru x w/cats, mgw short throw, h&r sports, 17in black deep dishes 
|
|
|
|
|
| Thread Tools | |
| Display Modes | |
Linear Mode
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Subframe Connector Question | Jack The Ripper | Modular 4.6L Tech | 9 | 08-31-2006 01:25 PM |
| Randy: Can you ID this for me? | wythors | The Parts Desk | 2 | 07-05-2006 08:22 AM |
| New 18 inch Black Cobra rims with tire 675 Shipped | 66pony | Mustang Classifieds | 3 | 04-10-2006 06:40 PM |
| New 79-04 Steeda Sport Springs | DarkSith | Mustang Classifieds | 0 | 08-29-2005 02:50 PM |
| best way to launch | 03stangblue | Drag Racing! | 13 | 07-09-2005 10:52 AM |