what mods next???

"94" 5.0 · 04-25-2005, 10:00 PM

i have a 94GT 5 spd,my mods are in the signature.I know i need a shifter and that is next but what is after that preferably something that yields horsepower.is a chip worth the money at this point.any input would be greatly appreciated.

spike_africa · 04-26-2005, 09:08 AM

you need a cam and heads and intake badly before you get a chip. your heads basicly suck deek. If i was you i would serach around for some nice used performance heads. i see them on ebay alot. also get a nice upper and lower intake ot match. then save for cam then get a chip.or get a cam first for some extra power then a set of heads and intake manifolds. m ei would do the cam first cause its cheaper and i love the sound. but keep in mind when choosing the cam that you'll want it ot work with a good flowing set of heads later on.

"94" 5.0 · 04-27-2005, 09:42 PM

thanks for the info,i was thinking it may be time to dig into the motor but thats where the money starts getting big so i figured i'd see if there was something else i was missing.i have 160k on the car with no signs of any internal problems but will probably go through the whole thing.Any other suggestions on rods, pistons,crank,other internals???any matched kits that are good?

spike_africa · 04-28-2005, 08:00 AM

summit raicng has kits to rebuild them for fairly cheap they are good pices. you might wanna check them out. also if you dont wanna get into the motor yet a set of under drive pulleys will add a few ponies. also a upper intake manifold setup ant to hard to install and will add some power. and doesnt cost to much you look around the internet i bet you cna get some nices pices for cheap.

drewbhot · 05-09-2005, 01:36 PM

I have a 95 and I would say, I agree with the pulleys, but don't forget about those restrictive exhaust manifold. I could feel the difference when I put headers on my car. Sounds better too. Remember, long tubes are better with superchargers, shorties are better without. :toothy9:

djstallyin · 05-14-2005, 03:52 PM

hey how much work did it take to swap the 4.6 out of the 94 and put in a 5.0, i was thinking about doing the same thing to my 2000v6

04DarkShadowGT · 05-15-2005, 08:00 AM

Quote:

Originally Posted by drewbhot

I have a 95 and I would say, I agree with the pulleys, but don't forget about those restrictive exhaust manifold. I could feel the difference when I put headers on my car. Sounds better too. Remember, long tubes are better with superchargers, shorties are better without. :toothy9:

Is it different for a 5.0, because long tubes on a 4.6 are better N/A or with a blower.

spike_africa · 05-15-2005, 09:03 AM

Quote:

Originally Posted by djstallyin

hey how much work did it take to swap the 4.6 out of the 94 and put in a 5.0, i was thinking about doing the same thing to my 2000v6

94-95 are 302 cars. the 281ci isnt till 96.

2002BLGT · 05-15-2005, 10:36 AM

heads ( their are alot of choices .....GT40 Y303 's are cheap right now from numerous places like buyfordracing.com , parkway ford , etc.... ) keep in mind that GT40P heads require exhaust modifications to work right because of the spark plug location also thumperoforangpark.com does a good job on porting the stock heads .....trickflow stage 1 cam is a good cam on stock bottom ends.......then the intake needs to be addressed , pretty much anything is better than stock in this department ....I have a typhoon which is a knock off of the edelbrock RPM intake and it works great and fit great and was about half the price ( www.professional-products.com ) , trickflow and holley have package deals which work really great too but are more expensive .....dont forget the extras you will need too and upgrade to a bigger intake pump ....some say you need to upgrade to 24 lbs injectors but trust me you will be fine ...get an adjustable fuel pressure regulator and if it seems lean you can add some fuel pressure to accomidate it ....hope this helps

wade95 · 05-18-2005, 09:46 AM

I dont know what your final plans are for the car, but we can get these cars relatively healthy w/bolt ons. Im shooting for 260hp N/A and am currently at 240 w/the bolt ons in my sig. Im hoping that w/addition of LT headers and ProChamber H pipe that this will get me REAL close. After exhaust I will be tapped out for bolt ons unless I do TB and MassAirMeter. The chip, from what I read, is not worth it until you have a motor put together that has a little more "go" built into it. Im sure you have heard that our cars hate cam swaps, but from the research I have done, there are cams out there that are "plug and play" for our computers. I'll keep ya posted on what I end up with. Wade

"94" 5.0 · 05-18-2005, 09:27 PM

thanks alot for all the input.i have checked out the typhoon intake upper and lower package and thought it looked awesome for the price as mentioned,is there a big difference over stock power wise i mean, top end power i guess is what im looking for my car pulls hard to about 5300rpm and then falls flat on its face

04-25-2005, 10:00 PM	#1 (permalink)
"94" 5.0 Junior Member Join Date: Feb 2005 Location: elizabethtown,kentucky Posts: 29	what mods next??? i have a 94GT 5 spd,my mods are in the signature.I know i need a shifter and that is next but what is after that preferably something that yields horsepower.is a chip worth the money at this point.any input would be greatly appreciated. __________________ 1994 GT 5.0 5-speed BBK O/R H-pipe flowmaster 2 chamber densecharger(demolet motorsports)CAI 3.90 motive gears BBK progressive rate springs king cobra clutch air pump and smog system removed and shorter belt

04-26-2005, 09:08 AM	#2 (permalink)
spike_africa Administrator Join Date: Sep 2004 Location: Orlando,Florida Posts: 6,968	you need a cam and heads and intake badly before you get a chip. your heads basicly suck deek. If i was you i would serach around for some nice used performance heads. i see them on ebay alot. also get a nice upper and lower intake ot match. then save for cam then get a chip.or get a cam first for some extra power then a set of heads and intake manifolds. m ei would do the cam first cause its cheaper and i love the sound. but keep in mind when choosing the cam that you'll want it ot work with a good flowing set of heads later on. __________________ Dustin 2002 GT Mustang 5-Speed Drag Radials,Sprayed,Powershifted WOOO HOOOO!

04-27-2005, 09:42 PM	#3 (permalink)
"94" 5.0 Junior Member Join Date: Feb 2005 Location: elizabethtown,kentucky Posts: 29	thanks for the info,i was thinking it may be time to dig into the motor but thats where the money starts getting big so i figured i'd see if there was something else i was missing.i have 160k on the car with no signs of any internal problems but will probably go through the whole thing.Any other suggestions on rods, pistons,crank,other internals???any matched kits that are good? __________________ 1994 GT 5.0 5-speed BBK O/R H-pipe flowmaster 2 chamber densecharger(demolet motorsports)CAI 3.90 motive gears BBK progressive rate springs king cobra clutch air pump and smog system removed and shorter belt

04-28-2005, 08:00 AM	#4 (permalink)
spike_africa Administrator Join Date: Sep 2004 Location: Orlando,Florida Posts: 6,968	summit raicng has kits to rebuild them for fairly cheap they are good pices. you might wanna check them out. also if you dont wanna get into the motor yet a set of under drive pulleys will add a few ponies. also a upper intake manifold setup ant to hard to install and will add some power. and doesnt cost to much you look around the internet i bet you cna get some nices pices for cheap. __________________ Dustin 2002 GT Mustang 5-Speed Drag Radials,Sprayed,Powershifted WOOO HOOOO!

05-18-2005, 09:46 AM	#10 (permalink)
wade95 Senior Member Join Date: Jan 2005 Location: Tarpon Springs, FL Posts: 503	I dont know what your final plans are for the car, but we can get these cars relatively healthy w/bolt ons. Im shooting for 260hp N/A and am currently at 240 w/the bolt ons in my sig. Im hoping that w/addition of LT headers and ProChamber H pipe that this will get me REAL close. After exhaust I will be tapped out for bolt ons unless I do TB and MassAirMeter. The chip, from what I read, is not worth it until you have a motor put together that has a little more "go" built into it. Im sure you have heard that our cars hate cam swaps, but from the research I have done, there are cams out there that are "plug and play" for our computers. I'll keep ya posted on what I end up with. Wade __________________

05-09-2005, 01:36 PM	#5 (permalink)
drewbhot Hell yes I street race!! Join Date: May 2005 Location: Norfolk VA Posts: 25	I have a 95 and I would say, I agree with the pulleys, but don't forget about those restrictive exhaust manifold. I could feel the difference when I put headers on my car. Sounds better too. Remember, long tubes are better with superchargers, shorties are better without. :toothy9:

05-14-2005, 03:52 PM	#6 (permalink)
djstallyin Junior Member Join Date: May 2005 Posts: 1	hey how much work did it take to swap the 4.6 out of the 94 and put in a 5.0, i was thinking about doing the same thing to my 2000v6

05-15-2005, 10:36 AM	#9 (permalink)
2002BLGT Junior Member Join Date: Dec 2004 Posts: 8	heads ( their are alot of choices .....GT40 Y303 's are cheap right now from numerous places like buyfordracing.com , parkway ford , etc.... ) keep in mind that GT40P heads require exhaust modifications to work right because of the spark plug location also thumperoforangpark.com does a good job on porting the stock heads .....trickflow stage 1 cam is a good cam on stock bottom ends.......then the intake needs to be addressed , pretty much anything is better than stock in this department ....I have a typhoon which is a knock off of the edelbrock RPM intake and it works great and fit great and was about half the price ( www.professional-products.com ) , trickflow and holley have package deals which work really great too but are more expensive .....dont forget the extras you will need too and upgrade to a bigger intake pump ....some say you need to upgrade to 24 lbs injectors but trust me you will be fine ...get an adjustable fuel pressure regulator and if it seems lean you can add some fuel pressure to accomidate it ....hope this helps

05-18-2005, 09:27 PM	#11 (permalink)
"94" 5.0 Junior Member Join Date: Feb 2005 Location: elizabethtown,kentucky Posts: 29	thanks alot for all the input.i have checked out the typhoon intake upper and lower package and thought it looked awesome for the price as mentioned,is there a big difference over stock power wise i mean, top end power i guess is what im looking for my car pulls hard to about 5300rpm and then falls flat on its face __________________ 1994 GT 5.0 5-speed BBK O/R H-pipe flowmaster 2 chamber densecharger(demolet motorsports)CAI 3.90 motive gears BBK progressive rate springs king cobra clutch air pump and smog system removed and shorter belt

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Lots of Great Mustang Racing	WaterDR	Videos	2	03-13-2006 08:51 AM
Fr500 Rims Status??	XbcSharpShooter	AmericanMuscle	1	11-27-2005 03:48 PM
Intake manifold leak maybe?	silvergt	Modular 4.6L Tech	9	08-02-2005 02:28 PM
first use of porter cable	fast01gt	Pictures	11	07-20-2005 07:21 AM