03-04 cobra blower on 01 mustang gt??
#2
nope, not gonna' happen, wont work or fit on anything excecpt a DOHC. whatever you saw was either bullshit, photoshopped or a whole-lotta' green spent on something that didn't need it in the 1st place. now you can put a blower on your car, just not the one off a DOHC Cobra
#3
I remember seeing something about that....it might be helpful to provide the link so people can see it. Usually anything is possible with enough money and time, but post up the link so we can check it out.
#4
nope, not gonna' happen, wont work or fit on anything excecpt a DOHC. whatever you saw was either bullshit, photoshopped or a whole-lotta' green spent on something that didn't need it in the 1st place. now you can put a blower on your car, just not the one off a DOHC Cobra
#5
As for this topic. Check out http://www.miniterminatorsforum.com/
Forum started by the guy/guys who have done or are doing the Eaton swap onto their sixes.
Forum started by the guy/guys who have done or are doing the Eaton swap onto their sixes.
#6
well if it is true, I think its as waste of time and money when you can buy s/c kits made for v6's. just sounds like someone has to-much free time on thier hands or its just an M90 off a T-bird/XR7 wth the factory blower, which is easy to-do but not a DOHC blower on a SOHC and as the thread was started and asked if he could do the Cobra blower on a GT (not a v6) and I still say IT IS NOT COST EFFICTIVE TO-DO ON A 2V and I still stand by my comment
#8
Just an FYI.
The V6 market has it's little tid bits most people don't know or care to know about us as a community. Kinda fun though, being apart of a sort of "cult" I guess you could call it.
#9
well if it is true, I think its as waste of time and money when you can buy s/c kits made for v6's. just sounds like someone has to-much free time on thier hands or its just an M90 off a T-bird/XR7 wth the factory blower, which is easy to-do but not a DOHC blower on a SOHC and as the thread was started and asked if he could do the Cobra blower on a GT (not a v6) and I still say IT IS NOT COST EFFICTIVE TO-DO ON A 2V and I still stand by my comment
It's the M112 Eaton that most 99+ guys are going with.
Don't you think you should really look into something before making a comment or stating an opinion?
#10
its www.mustangworld.com and go to the pic of 99-04 an its the red 2002 v6 the newest one an it has the 03 04 blower
#11
no I do not. I call it as I see it and if you read the original post carefully, you 'll see the original poster was asking if it was cost-effective to do a '03 Cobra blower on a GT and the ansewer is still NO
#13
yes i saw it done to a v6 so i figure i could do it to my gt the bolt patterns are the same people tell me an i would just need to get the pulleys and things and it will work it doesnt matter on cost efficient an i dont just wanna buy a blower from a kit or anything
#15
yes i saw it done to a v6 so i figure i could do it to my gt the bolt patterns are the same people tell me an i would just need to get the pulleys and things and it will work it doesnt matter on cost efficient an i dont just wanna buy a blower from a kit or anything
what are you going to-do for an intake manifold? section one off a Lightning?
where would you attach the blower belt idlers and tensioners? its not that easy, as Dan stated get a kit either Paxton/Vortech or KB
#18
I would go with the KB setup. For $5-6k it's a twin screw, innercooled system that's proven. I did my setup because there are no positive displacement setups for the splitport 6er, yet. I ended up spending under $3k and that included the dyno tune. It took me one winter to get everything designed, made, and purchased and one week to install and tune it. The best part of this project is the fact that I did it with my daily driver and it was only out of commission for the week of the install. I didn't have a mockup engine.
#19
Ahem....Randy has about as much experience in his little finger as most of us have in our entire bodies. Not only is the guy been racing longer then most of you been shitting, but he is well known in the mustang racing community.
Does the guy know everything? Nope....still learning right Randy?
But, this is no easy swap. I suppose that if someone were getting these blowers for fee and had lots of time, then perhas the effort is worth the engineering challenge. But when you are old like me an Randy, we place a much higher value on our time.
Who knows, maybe someone is fabricating a "kit" for these things. One thing is for sure, there are a lot of these blowers sitting on shelves in guys garages because once you take them off a cobra, they are paper weights.
Does the guy know everything? Nope....still learning right Randy?
But, this is no easy swap. I suppose that if someone were getting these blowers for fee and had lots of time, then perhas the effort is worth the engineering challenge. But when you are old like me an Randy, we place a much higher value on our time.
Who knows, maybe someone is fabricating a "kit" for these things. One thing is for sure, there are a lot of these blowers sitting on shelves in guys garages because once you take them off a cobra, they are paper weights.
Thread
Thread Starter
Forum
Replies
Last Post