Brake Rotors

02-STANG-GT · 11-08-2005, 03:51 PM

Just purchased a set of Power Slot[OE] rotors for my 02, Anybody changed rotors, is it simple?Any surprises I should know about? Real satisfied the way they look!

spike_africa · 11-08-2005, 05:19 PM

easy as taken the wheel off, unbolt the caliper, move it out of the way pull off old rotor slide new one on and reinstall everything its easy.

02-STANG-GT · 11-08-2005, 05:26 PM

OK Thanks , thats what I want to hear! Doing it this weekend.

spike_africa · 11-08-2005, 08:09 PM

no problem, its really that easy too, but you might as well add some good pads while your in there. and do yourself a favor dont ubolt the brake line from the caliper its not needed to get it out of the way and this way you dont have to bleed the brakes.

02-STANG-GT · 11-12-2005, 03:31 PM

Brake rotor change didn't go as planned, well to begin with ,they sent me what appears to be 4 rear rotors, taking care of that tommorrow, next says I must install new pads, never done that on a mustang,does anyone know ia site where i can get info on [how to]pad replacement? 2002

Islander03GT · 11-12-2005, 07:58 PM

Pad replacement is pretty self explanitory if you're already planning to do the rotors. Pads sit inside the calipers, remove them and clip the new ones in. Make sure to use some no-squeak stuff on the backside of them before installing.

Also, you're going to need the caliper tool for the rear... rent it from Autozone/Kragen

spike_africa · 11-12-2005, 08:12 PM

you odnt have to change pads at all thats bs.

Shambles · 11-12-2005, 11:24 PM

You dont ABSOLUTELY have to change the pads but it is reccommended. This is because the pads have to break into the brakes. If you want to use your stock pads drive around a bit and hit the brakes hard a few times to brake the pads into the new rotors.

If you are going to get new pads Powerslot reccomends getting Hawk Pads. I also reccomend Hawks, because theyre bitchin!

02-STANG-GT · 11-13-2005, 03:15 PM

OK, Here goes, Returned rotors today and they were in the wrong box from power slot, 2 rear rotors were in box marked front,also bought set of hawk pads, i think I need a repair manual , thanks for the advise ! Have to say though after all I been thru these are nice looking rotors for the buck !

*madmatt* · 11-13-2005, 07:09 PM

Id definately recommend the manual, just because of the torque specs they give you in it. Also, maybe look into just some Brembo blank rotors. Cheaper than the powerslots.

MattJ · 11-13-2005, 07:47 PM

How much are hawk pads?

Shambles · 11-13-2005, 09:02 PM

Youll find out when we finish our pricing with powerslot...

Oops did I say too much?

stangspeed · 11-13-2005, 10:01 PM

Quote:

Originally Posted by MTShambles

Youll find out when we finish our pricing with powerslot...

Oops did I say too much?

Hurry, hurry...I need new brakes very soon. I would rather buy them here than from somewhere else..

MattJ · 11-13-2005, 10:24 PM

i need brakes too but im not worried untill april is coming up. bob said hes getting the cobra 10th anniversarys and I still dont see em available, or the email I was told I would get when they come in.

02-STANG-GT · 11-14-2005, 06:34 PM

HAWK PADS Total front / rear $142 , , found a manual "haynes" $22, you will like these rotors !

jeredan2003 · 11-14-2005, 07:07 PM

Ill save up and buy the Cobra R Baer Kit. Its about $500 for the front but it would stop soooo much better and they will look great with the dark shadow grey. When I get those Ill probably end up getting the Baer 13" rear kit at the same time. Its like $250.

NoKturnaL · 11-15-2005, 11:41 AM

Quote:

Originally Posted by jeredan2003

Ill save up and buy the Cobra R Baer Kit. Its about $500 for the front but it would stop soooo much better and they will look great with the dark shadow grey. When I get those Ill probably end up getting the Baer 13" rear kit at the same time. Its like $250.

where can I find that Cobra R baer kit?

jeredan2003 · 11-16-2005, 07:45 AM

Quote:

Originally Posted by V8 SyndicateZ

where can I find that Cobra R baer kit?

Just look at ads in magazines such as 5.0 Mustang or Muscle Mustangs and Fast Fords. Theyre sold by a few different companies in there. Also you can probably go to the 5.0 Resto. web site. Im pretty sure they sell them too. Ive seen prices for the kit range from $499-700.

*4.6 Love* · 11-16-2005, 01:31 PM

Quote:

Originally Posted by V8 SyndicateZ

where can I find that Cobra R baer kit?

You won't because the brakes on the cobra R were made by brembo.

11-08-2005, 03:51 PM	#1 (permalink)
02-STANG-GT Senior Member Join Date: Jun 2005 Posts: 125	Brake Rotors Just purchased a set of Power Slot[OE] rotors for my 02, Anybody changed rotors, is it simple?Any surprises I should know about? Real satisfied the way they look!

11-08-2005, 05:19 PM	#2 (permalink)
spike_africa Administrator Join Date: Sep 2004 Location: Orlando,Florida Posts: 7,080	easy as taken the wheel off, unbolt the caliper, move it out of the way pull off old rotor slide new one on and reinstall everything its easy. __________________ Dustin 2002 GT Mustang 5-Speed Drag Radials,Sprayed,Powershifted WOOO HOOOO!

11-08-2005, 08:09 PM	#4 (permalink)
spike_africa Administrator Join Date: Sep 2004 Location: Orlando,Florida Posts: 7,080	no problem, its really that easy too, but you might as well add some good pads while your in there. and do yourself a favor dont ubolt the brake line from the caliper its not needed to get it out of the way and this way you dont have to bleed the brakes. __________________ Dustin 2002 GT Mustang 5-Speed Drag Radials,Sprayed,Powershifted WOOO HOOOO!

11-12-2005, 07:58 PM	#6 (permalink)
Islander03GT Senior Member Join Date: Dec 2004 Location: Simi Valley, Ca Posts: 717	Pad replacement is pretty self explanitory if you're already planning to do the rotors. Pads sit inside the calipers, remove them and clip the new ones in. Make sure to use some no-squeak stuff on the backside of them before installing. Also, you're going to need the caliper tool for the rear... rent it from Autozone/Kragen __________________ John V 06 Honda Accord SE- Daily Driver 83 Jeep Cherokee W/T- Off Road Toy 02 Mineral Gray V6 Vert- Girlfriends No more: 03 GT- The Problem Child

11-12-2005, 08:12 PM	#7 (permalink)
spike_africa Administrator Join Date: Sep 2004 Location: Orlando,Florida Posts: 7,080	you odnt have to change pads at all thats bs. __________________ Dustin 2002 GT Mustang 5-Speed Drag Radials,Sprayed,Powershifted WOOO HOOOO!

11-08-2005, 05:26 PM	#3 (permalink)
02-STANG-GT Senior Member Join Date: Jun 2005 Posts: 125	OK Thanks , thats what I want to hear! Doing it this weekend.

11-12-2005, 03:31 PM	#5 (permalink)
02-STANG-GT Senior Member Join Date: Jun 2005 Posts: 125	Brake rotor change didn't go as planned, well to begin with ,they sent me what appears to be 4 rear rotors, taking care of that tommorrow, next says I must install new pads, never done that on a mustang,does anyone know ia site where i can get info on [how to]pad replacement? 2002

11-12-2005, 11:24 PM	#8 (permalink)
Shambles The Baninator! Join Date: Mar 2005 Location: Springfield, PA Posts: 2,652	You dont ABSOLUTELY have to change the pads but it is reccommended. This is because the pads have to break into the brakes. If you want to use your stock pads drive around a bit and hit the brakes hard a few times to brake the pads into the new rotors. If you are going to get new pads Powerslot reccomends getting Hawk Pads. I also reccomend Hawks, because theyre bitchin! __________________ Chris "Shambles" Chamblee

11-13-2005, 03:15 PM	#9 (permalink)
02-STANG-GT Senior Member Join Date: Jun 2005 Posts: 125	OK, Here goes, Returned rotors today and they were in the wrong box from power slot, 2 rear rotors were in box marked front,also bought set of hawk pads, i think I need a repair manual , thanks for the advise ! Have to say though after all I been thru these are nice looking rotors for the buck !

11-13-2005, 07:09 PM	#10 (permalink)
madmatt Traitor...lol Join Date: Sep 2004 Location: Lexington, SC Posts: 7,912	Id definately recommend the manual, just because of the torque specs they give you in it. Also, maybe look into just some Brembo blank rotors. Cheaper than the powerslots. __________________ RPMPlanets

11-13-2005, 07:47 PM	#11 (permalink)
MattJ Senior Member Join Date: Dec 2004 Location: Racine, WI Posts: 10,243	How much are hawk pads? __________________ 2001 Mustang GT Premium - Mineral Grey

11-13-2005, 09:02 PM	#12 (permalink)
Shambles The Baninator! Join Date: Mar 2005 Location: Springfield, PA Posts: 2,652	Youll find out when we finish our pricing with powerslot... Oops did I say too much? __________________ Chris "Shambles" Chamblee

11-13-2005, 10:24 PM	#14 (permalink)
MattJ Senior Member Join Date: Dec 2004 Location: Racine, WI Posts: 10,243	i need brakes too but im not worried untill april is coming up. bob said hes getting the cobra 10th anniversarys and I still dont see em available, or the email I was told I would get when they come in. __________________ 2001 Mustang GT Premium - Mineral Grey

11-14-2005, 06:34 PM	#15 (permalink)
02-STANG-GT Senior Member Join Date: Jun 2005 Posts: 125	HAWK PADS Total front / rear $142 , , found a manual "haynes" $22, you will like these rotors !

11-14-2005, 07:07 PM	#16 (permalink)
jeredan2003 Senior Member Join Date: Nov 2004 Location: Murfreesboro, TN Posts: 1,788	Ill save up and buy the Cobra R Baer Kit. Its about $500 for the front but it would stop soooo much better and they will look great with the dark shadow grey. When I get those Ill probably end up getting the Baer 13" rear kit at the same time. Its like $250. __________________ 2003 DSG GT 5-speed Hellion 62mm and Flowmaster catback..... My bonestock 2v engine had been through 2 years of NX 100 shot, 3 years running 8-12lbs vortech s-trim, got into boost daily while racing on the weekends, had 157,000 miles on it, and was running like new

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Camera	StormsGT	Pictures	15	10-25-2006 09:13 PM
BBK 65mm Throttle Body (99-2000 V6)	New Products	New American Muscle Products	0	10-04-2006 08:06 AM
Logan Motorsports 2V intake	03gtmustang	Modular 4.6L Tech	6	10-03-2006 11:20 AM
Something i don't understand about the "da vinci code"...	dannyb785	The Lounge	24	05-23-2006 12:21 AM
My Brother's TV Show Premier's Tonight	WaterDR	The Lounge	6	09-15-2005 01:44 PM