Mustang Boards

Mustang Boards (/)
-   V6 Tech Forums (https://mustangboards.com/v6-tech-forums/)
-   -   how to remove emblems?? (https://mustangboards.com/v6-tech-forums/11167-how-remove-emblems.html)

Jonny5 03-22-2006 10:54 PM

how to remove emblems??
 
Are the emblems on the '03's attached adhesively? If so, what's the best way to remove them without damaging the paint?

Thanks for any help!!

And on a side note......
I have a black pony edition- just put on my chin spoiler and must say it really cleaned up the look of the front end. Other mods: 18" wheels, tinted windows, dual exhaust, cold air intake, shorty antenna

soon to come: grill delete and I gotta get this thing lowered!!!!
ANY SUGGESTIONS FOR OTHER MODS WELCOME!!

whitethunder46 03-22-2006 10:57 PM

Way I do is take a screw driver. Behind the screw driver I put either a towel/cloth/sponge so that it wont touch the paint. They just peal off. After that I use goo gone to take off the remaining adhesive (there will be some)

All the emblems have studs on the back of them so there will be a hole on the fenders/trunk still if you were planning on going badgeless.

spike_africa 03-23-2006 07:37 AM

use a blow dryer and heat them up and it will just peel right off and leaves little mess, then use goo gone and it takes all the goo left off of there.

swervo 03-23-2006 02:20 PM

Those other ideas work, but I find this much easier. Like Spike said, heat up the emblem with a heat gun/hair drier and get it nice and hot. Get some fishing line or dental foss (fishing line is better) and saw the emblem off. Next just pull off the rest of the two sided tape that's left over and use some adheasive remover to get all the adhesive off. Next get some rubbing alcohol and clean up the area. I think this is the best and easiest way to do it without scratching your paint.

Grimmz 03-23-2006 02:44 PM


Originally Posted by swervo
Those other ideas work, but I find this much easier. Like Spike said, heat up the emblem with a heat gun/hair drier and get it nice and hot. Get some fishing line or dental foss (fishing line is better) and saw the emblem off. Next just pull off the rest of the two sided tape that's left over and use some adheasive remover to get all the adhesive off. Next get some rubbing alcohol and clean up the area. I think this is the best and easiest way to do it without scratching your paint.

do you guyz also have some tips on filling in the holes left over?... I'm wana remove my FORD emblem to even out the rear a bit... any cheap/easy ways to do this without having to go to a painter... Oh and how big of a hole am I looking at?

whitethunder46 03-23-2006 03:08 PM


Originally Posted by Grimmz
do you guyz also have some tips on filling in the holes left over?... I'm wana remove my FORD emblem to even out the rear a bit... any cheap/easy ways to do this without having to go to a painter... Oh and how big of a hole am I looking at?

1/8 inch diameter, maybe 1/4

Jack The Ripper 03-23-2006 05:49 PM

Use dental flos. use it to saw behind the emblem then once you got the foam backing cut, you can pull the emblem off, get some 3mm adhesive remover and yer done!

66pony 03-23-2006 06:19 PM

just had my filed you have to paint
 
i just shaved all my emblems and you have to paint after you fill them in it looks really good though its worth it


All times are GMT -7. The time now is 08:25 AM.


© 2024 MH Sub I, LLC dba Internet Brands