upper control arms

gt1 · 09-24-2006, 08:05 AM

anybody know the torque settings for upper control arms , axle side ? and frame side? for my 99 gt, i'am using frpp upper arms. thanx

bassman97 · 09-25-2006, 10:52 AM

Hate to inform you but the FRPP RUCA are just the stock 99-04 pieces.

gt1 · 09-25-2006, 05:19 PM

yes thanks, what is the torque setting? and actually they are not, part number m-5500-a come with bushing twice as stiff then production bushings and arms are a little bit longer

bassman97 · 09-25-2006, 06:02 PM

http://www.maximummotorsports.com/st...roducts_id=544
Bushings used are the same as the production SN95 units.
Anyway, I believe you torque them down to 111 ft*lbs but this has to be done while the suspension is loaded.

*03gtmustang* · 09-25-2006, 06:13 PM

Quote:

Originally Posted by bassman97

Anyway, I believe you torque them down to 111 ft*lbs but this has to be done while the suspension is loaded.

That would work fine.

gt1 · 09-26-2006, 01:19 PM

ok thanx,

r3dn3ck · 09-27-2006, 11:43 AM

some sources say the bushing is higher durometer than stock on the FRPP uppers but it's rubber still so I wouldn't put much stock in it being too helpful. The UCA's need to be set on flexible bushings or you'll bind up hella bad anyway.

I always cinch mine down to 70lbs all the way around but, I'm all the time under my car tinkering so it's nicer to not have to move the world to pull a bolt...just personal preferance.

09-24-2006, 08:05 AM	#1 (permalink)
gt1 Junior Member Join Date: Feb 2006 Posts: 3	upper control arms anybody know the torque settings for upper control arms , axle side ? and frame side? for my 99 gt, i'am using frpp upper arms. thanx

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
performance question?	blackbird98	General Tech Forum	3	11-30-2006 01:20 AM
Here you go Foncarelli	Twin Turbo 330	Pictures	22	07-21-2006 10:18 AM
opinion on rims...	m0nkeh	Tire and Wheel Talk!	6	04-04-2006 08:41 PM
slp and prochamber??	stevestang81	Modular 4.6L Tech	12	10-24-2005 04:27 PM
Member Of The Month	NoKturnaL	The Lounge	17	12-21-2004 11:32 AM

09-25-2006, 10:52 AM	#2 (permalink)
bassman97 blank Join Date: Jun 2006 Location: North Jersey Posts: 1,373	Hate to inform you but the FRPP RUCA are just the stock 99-04 pieces.

09-25-2006, 05:19 PM	#3 (permalink)
gt1 Junior Member Join Date: Feb 2006 Posts: 3	yes thanks, what is the torque setting? and actually they are not, part number m-5500-a come with bushing twice as stiff then production bushings and arms are a little bit longer

09-25-2006, 06:02 PM	#4 (permalink)
bassman97 blank Join Date: Jun 2006 Location: North Jersey Posts: 1,373	http://www.maximummotorsports.com/st...roducts_id=544 Bushings used are the same as the production SN95 units. Anyway, I believe you torque them down to 111 ft*lbs but this has to be done while the suspension is loaded.

09-26-2006, 01:19 PM	#6 (permalink)
gt1 Junior Member Join Date: Feb 2006 Posts: 3	ok thanx,

09-27-2006, 11:43 AM	#7 (permalink)
r3dn3ck Wowbagger hates me too! Join Date: Nov 2005 Location: Magrathea/California Posts: 6,708	some sources say the bushing is higher durometer than stock on the FRPP uppers but it's rubber still so I wouldn't put much stock in it being too helpful. The UCA's need to be set on flexible bushings or you'll bind up hella bad anyway. I always cinch mine down to 70lbs all the way around but, I'm all the time under my car tinkering so it's nicer to not have to move the world to pull a bolt...just personal preferance.