Tensioner

bassman97 · 02-29-2008, 12:39 PM

How much force is required to release the tension on the accessory belt? The Haynes manual says to use a 1/2 breaker bar but the best I have is a 3/8" to 1/2" adaptor, old socket wrench, and a long rod which works fine for my wheels but probably won't do if more torque is needed.

bossman302 · 02-29-2008, 12:49 PM

Get as much leverage as you can and fair amount of muscle should do it.

bassman97 · 02-29-2008, 02:13 PM

Well, I figured muscle is required but what I'm concerned w/ is if wheel lug nuts torque to 100 ft-lbs can bend the handle on the socket wrench I use as a breaker bar, something torque down tighter will probably shear the 3/8" square portion.

bossman302 · 02-29-2008, 02:49 PM

I don't think it will take 100 ft lbs to release the tension on the belt. I would say no more that 80 ft lbs. I use a 3/8 socket wrench with a jack handle to get more leverage and had no isses. You should be ok, but as always anything can happen.

bassman97 · 02-29-2008, 08:40 PM

Actually, that's what I use for a breaker bar. If that works for you, then it's perfect for me. Thanks for the help.

02-29-2008, 12:39 PM	#1 (permalink)
bassman97 blank Join Date: Jun 2006 Location: North Jersey Posts: 1,495	Tensioner How much force is required to release the tension on the accessory belt? The Haynes manual says to use a 1/2 breaker bar but the best I have is a 3/8" to 1/2" adaptor, old socket wrench, and a long rod which works fine for my wheels but probably won't do if more torque is needed.

02-29-2008, 12:49 PM	#2 (permalink)
bossman302 Senior Member Join Date: Apr 2006 Location: Sacramento, CA Posts: 177	Get as much leverage as you can and fair amount of muscle should do it. __________________ Mineral gray 2002 Mustang GT manual 5 speed. Maximum Motor sport suspension. Forge 4.6 with VT stg 2 cams. BBK 75mm tb and LT's. JLT RAI. 290 HP and 308 tq at the wheels.

02-29-2008, 02:49 PM	#4 (permalink)
bossman302 Senior Member Join Date: Apr 2006 Location: Sacramento, CA Posts: 177	I don't think it will take 100 ft lbs to release the tension on the belt. I would say no more that 80 ft lbs. I use a 3/8 socket wrench with a jack handle to get more leverage and had no isses. You should be ok, but as always anything can happen. __________________ Mineral gray 2002 Mustang GT manual 5 speed. Maximum Motor sport suspension. Forge 4.6 with VT stg 2 cams. BBK 75mm tb and LT's. JLT RAI. 290 HP and 308 tq at the wheels.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-29-2008, 02:13 PM	#3 (permalink)
bassman97 blank Join Date: Jun 2006 Location: North Jersey Posts: 1,495	Well, I figured muscle is required but what I'm concerned w/ is if wheel lug nuts torque to 100 ft-lbs can bend the handle on the socket wrench I use as a breaker bar, something torque down tighter will probably shear the 3/8" square portion.

02-29-2008, 08:40 PM	#5 (permalink)
bassman97 blank Join Date: Jun 2006 Location: North Jersey Posts: 1,495	Actually, that's what I use for a breaker bar. If that works for you, then it's perfect for me. Thanks for the help.