88 5.0 problems

bigdog1011972005 · 05-31-2005, 03:32 PM

I just bought a 88 5.0 the problem i am having is pulling my last hair. i have replaced the head gaskets and water pump but it still runs hot. also when i start it up it has a rough idle up and down and then when it gets warm its fine. could that be radiator. also when i set the timing with the plug out its fine but when i put the plug back in its all messed up. could that be the distributor? any help would be great. thanks adam

drewbhot · 06-01-2005, 01:35 PM

That sounds like a bunch of stuff? Runs hot? How hot? On the gauge, half way? About that? A tiny bit less then half way is about 180 so try to guess from there? Have you checked the thermostat? Take it out and heat it with a torch or boil it in some water. If it doesn't open or it takes a long time then that may be the problem. Could be a faulty sending unit, those are a few dollars, wouldn't hurt to change that. Is your cooling fan coming on? If not, is the fuse for it blown?

Idle? Plug in the spout connector, then unplug your IAC valve, you may have to play with the throttle body stop plate to get it to stay running, but check the idle then. Those things are notorious for cause problems like that.

bigdog1011972005 · 06-02-2005, 10:39 AM

it runs in the middle for a while but then when you take it for a drive it climbs all the way to the red line and stays. the funny thing is that it doesnt act like it is over heating, no knocks and no weird sounds like you would think. i took out the thermostat, it works fine, changed the sending unit, fan is fine. i think that it is my radiator, its start to steam after only running for a few mins. i am new to mustangs so what is a IAC and where is it? thanks for your help. thanks adam

05-31-2005, 03:32 PM	#1 (permalink)
bigdog1011972005 Junior Member Join Date: May 2005 Posts: 23	88 5.0 problems I just bought a 88 5.0 the problem i am having is pulling my last hair. i have replaced the head gaskets and water pump but it still runs hot. also when i start it up it has a rough idle up and down and then when it gets warm its fine. could that be radiator. also when i set the timing with the plug out its fine but when i put the plug back in its all messed up. could that be the distributor? any help would be great. thanks adam

06-02-2005, 10:39 AM	#3 (permalink)
bigdog1011972005 Junior Member Join Date: May 2005 Posts: 23	still having troubles it runs in the middle for a while but then when you take it for a drive it climbs all the way to the red line and stays. the funny thing is that it doesnt act like it is over heating, no knocks and no weird sounds like you would think. i took out the thermostat, it works fine, changed the sending unit, fan is fine. i think that it is my radiator, its start to steam after only running for a few mins. i am new to mustangs so what is a IAC and where is it? thanks for your help. thanks adam

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
couple new pics	ShapeShifter	Pictures	18	11-07-2006 07:29 AM
Interior Dome Light	Wonderwyrm	The Parts Desk	5	10-24-2006 10:12 AM
Ashtray Sleeper Nitrous Panel (87-93)	New Products	New American Muscle Products	0	09-30-2006 07:05 AM
Bad Business	Icefreezen	The Lounge	13	10-11-2005 07:33 AM
Pics of the New Dash Kit	Stevoneo	Pictures	14	03-14-2005 02:42 PM

06-01-2005, 01:35 PM	#2 (permalink)
drewbhot Hell yes I street race!! Join Date: May 2005 Location: Norfolk VA Posts: 25	That sounds like a bunch of stuff? Runs hot? How hot? On the gauge, half way? About that? A tiny bit less then half way is about 180 so try to guess from there? Have you checked the thermostat? Take it out and heat it with a torch or boil it in some water. If it doesn't open or it takes a long time then that may be the problem. Could be a faulty sending unit, those are a few dollars, wouldn't hurt to change that. Is your cooling fan coming on? If not, is the fuse for it blown? Idle? Plug in the spout connector, then unplug your IAC valve, you may have to play with the throttle body stop plate to get it to stay running, but check the idle then. Those things are notorious for cause problems like that.